Optimum security of spring tines
Clamp A retains the spring tine if it should brake, protecting the forage harvester or baler from damage
Strong and flexible rake tines
8 rake tines on each rotor ensure very good clean raking, close to 100%. Cranked tines are part of this high working quality. The adjustment from spreading to raking is quick and easy: You simply change the position of the rake tines using a spring loaded dowel. The rake tines are fabricated from high-class spring steel. ensuring long life and low maintenance costs.
Z 585 PRO
|Working width||5.60 m|
|No. of Rotors||4|
|Rake arms per Rotor||7|
|Rotor diameter||1.75 m|
Simple and sturdy transmission
A special V-belt drives both rotors and is kept tight by an automatically belt tensioner. Another example of JF's attention to detail helping ease the daily work load.
Good adaption to ground conditions
The wheels of the machine have been positioned with the shortest possible distance between them and the front rake tines. An even and steady performance, with good clean raking, can be achieved under all conditions
The shredder is meant to shred/chop wooden, fibrous, grass leaves, cardboard packing cases, waste fruit and vegetables, wooden boxes, pallets, etc. The fineness of the shredding material can be adjusted through a screen. The shredder can be operated either by electric motor or by diesel engine or by tractor PTO. The out put capacity of the equipment starts from 3 to 60 cub.mtr/hr.
Hay and Staw, Ear Corn, Small Grains: Shelled Corn, Milo, Wheat & Barley, Cardboard & Paper, Wood Chips & Bark, Silaged Bales. The TUB GRINDER has no belt, chain or gear box drives to wear out. This simplicity of design allows the TUB GRINDER to be sold at such a low price. The most astonishing feature of the TUB GRINDER is its lower horsepower requirements and smoother operation. The rotor cuts across the tub floor from the outside to the center and much of the grinding is done in the tub before the material reaches the main grinding area. The rotor is three to five times heavier per inch of shear length than competitive machines and this extra weight builds inertia that makes the TUB GRINDER the smoothest running grinder on the market and the easiest on tractor power take-offs.The capacity will surprise you. Ten to twenty ton per hour in fairly dry conditions with 70 to 80 horsepower can be expected. Also the TUB GRINDER uses shear plates instead of screens which makes it even more desirable in wet, tough conditions. Individually adjustable shear plates replace screens to control particle size, these shear plates are adjustable from ground level and can be adjusted with speed and ease.
A High Capacity-Low Cost grinder that can grind dairy quality alfalfa without getting it too fine. We can now grind this good quality alfalfa to the desired length for all operations. Any length from 2" to 6" stems. We accomplish this by using a special ALFALFA HAMMER that weighs 38 a piece. These hammers will stay extended in this good quality feed at 540 This lower tip speed does not powder the leaves. Horsepower requirement is reduced to about half (from 60 and up) and the capacity remains high. LOW PROFILE SPECIAL: Same as above but for the operator who wants to use a lower lift Skid Steer loader to feed the Tub Grinder. Only 7'4 high and 8 6 wide at the top of the tub.
PZ SERIES PROFESSION CHIPPING MACHINES
Wood chipper range includes machines able to reduce the volume of large masses of green or dry material, including logs and branches with diameters that vary fraom 10 to 25 cm, without excluding any other residues of pruning, scrubs, brambles and anything else resulting from maintenance of the woodland, avenues,parks, gardens and cemeteries. The machines can be built to operate in staitc conditions, or enabled for attachment to the 3-point hitch to be towed by a tractor or mounted on a trailer for road transport (at low or high speed).
The special features that distinguish this chipping machines is the large size of the feeding hopper of the material to be chipped, which are followed by two notched rollers which, with independent hydraulic activation, take the material to the cutting flywheel onto which the knives are attached. Long experience has allowed to structure this flywheel in a way to assure the best cutting effectiveness through time, without requiring particular maintenance interventions.
A "no stress" electronic protection device automatically adjusts the feed flow of the material to be chipped, in relation to the power available, according to the force of the amount of material being chipped. This device lengthens the machine's life. The chipped material is then expelled using the unloading conveyor, equipped with movable deflector that allows to direct the flow to the ground or towards a container (eg. transport vehicle container).
These chipping machines-backing the customer's requirements can be driven by tractor power-take-off (G), an autonomous Disel (M), or electric (E) motor.
These Pz series chipping machines distinguish themsilves for their capacity to reduce large volumes of green or dry material in very short times.
Max. Chipping Ømm
Roller width mm
Feeding hopper mm
|PZ 100||100||110||690 x 400|
|PZ 110||110||155||890 x 600|
|PZ 140||140||175||1000 x 640|
|PZ 150||150||220||1110 x 730|
|PZ 190||190||240||1220 x 700|
|PZ 210||210||300||1220 x 700|
|PZ 250||250||370||1350 x 886|
Soil Prerparation Equipments
Post Harvest Equipments
Garden & Horticulture Equipments
Forage & Dairy Equipments
Bio-Mass Collection & Process Equipments
We are committed to produce the best quality agro forestry equipment in the possible shortest time with the vision of passing technological advancements to Indian Farmers, during the years to come.